171 reactions · 15 shares | Check out these tips and tricks on properly piloting, spotting or centering a hole. | Practical Machinist | Facebook
2:46
171 reactions · 15 shares | Check out these tips and tricks on proper…
196.9K views3 weeks ago
FacebookPractical Machinist
"Just some manual tapping. Normally I would use the machine but with an M4x.7 tap I ain’t playing around! Guaranteed I’d have snapped this under power." Credit: IG User hammerdown_tools | Practical Machinist
0:28
"Just some manual tapping. Normally I would use the machine …
1.8M viewsDec 5, 2020
FacebookPractical Machinist
Introduction to 1-2-3 Blocks - Practical Machinist
Introduction to 1-2-3 Blocks - Practical Machinist
Mar 19, 2021
practicalmachinist.com
4.8K views | Take advantage of time saving features - and the legendary performance - of a compact machining center. | Practical Machinist | Facebook
1:03
4.8K views | Take advantage of time saving features - and the legendar…
4.8K views2 weeks ago
FacebookPractical Machinist
Did you know that it takes more than two days to produce an insert? | Practical Machinist
6:17
Did you know that it takes more than two days to produce an insert? | P…
146.9K viewsMar 8, 2018
FacebookPractical Machinist
Machinist tip of the day 💡 Credit: IG User octane_workholding | Practical Machinist
2:58
Machinist tip of the day 💡 Credit: IG User octane_workholding | Practic…
132.3K viewsJul 16, 2024
FacebookPractical Machinist
"A few deep hole tips. Use a carbide screw machine drill where the stiffness helps reduce the possibility of Euler buckling, which can cause a crooked hole trajectory. Use gentle feedrates to not enter buckling territory. Once you have a 10x to 15x depth, the drill is supported enough to stay on a relatively straight path. Just thought of the Oring trick today." Credit: IG User robinrenzetti | Practical Machinist
1:08
"A few deep hole tips. Use a carbide screw machine drill where the stiff…
15.8K viewsDec 19, 2023
FacebookPractical Machinist
7:49
Rebecca Wolfinger, owner of Mil-Spec Manufacturing , shares her e…
542 viewsFeb 8, 2024
FacebookPractical Machinist
3:13
14K views · 27 reactions | Tips and tricks to keep your coolant conce…
14.6K views2 weeks ago
FacebookPractical Machinist
31:11
Can you mill a part on a lathe? What about turning on a mill? The answ…
13.9K viewsApr 23, 2021
FacebookPractical Machinist
0:13
538K views · 2.7K reactions | Simple useful trick for small productions, …
538.5K views1 week ago
FacebookPractical Machinist
0:58
No screwing around. Sometimes manual is the way to go! 1-1/4 x 5 t…
1.6M viewsDec 30, 2019
FacebookPractical Machinist
0:12
You can swap out the vise’s standard threaded set screws for t…
4.8K viewsJan 6, 2020
FacebookPractical Machinist
1:01
15K views · 143 reactions | Drilling and threadmilling 25 holes with M…
15.3K views5 days ago
FacebookPractical Machinist
0:15
12K views · 90 reactions | Getting after it today on the mill! Credit: I…
12.8K views3 weeks ago
FacebookPractical Machinist
3:37
"Well, it started ok, tapped the first hole but lost the tap in the secon…
28.1K viewsFeb 13, 2023
FacebookPractical Machinist
0:05
Enter the Machinery's Handbook and Calculator Set giveaway. 1. S…
441 viewsApr 22, 2020
FacebookPractical Machinist
0:04
Challenge: Explain what is going on as if you were talking to a 5 year o…
10.9K viewsMar 18, 2023
FacebookPractical Machinist
0:41
Did YOU attend any trade shows in 2023? We went to one of the most …
9.5K viewsNov 29, 2023
FacebookPractical Machinist
0:48
"Hard turning the face of a D2 spindle rotor at 58 HRC. The 5C co…
43.7K viewsJul 17, 2021
FacebookPractical Machinist
0:36
405K views · 3.8K reactions | "I am very close to the final results. The …
405.5K views1 week ago
FacebookPractical Machinist
0:24
11K views · 119 reactions | Enter the Machinery's Handbook and...
11K views6 days ago
FacebookPractical Machinist
33:03
What's the best way to machine a perfectly round hole? Should you …
4.4K viewsMay 25, 2021
FacebookPractical Machinist
Hot-Rush Jobs: THREE THINGS You Need to Know | Machine Shop Tal…
74.3K viewsJul 24, 2024
YouTubePractical Machinist
12 Machinist Tips and Tricks for Beginners from an Old Pro
Oct 5, 2018
americanrotary.com
14:36
Circular Pocket Milling Tips
26K viewsNov 25, 2020
YouTubePractical Machinist
43:16
Introduction to CNC Lathe Programming
47K viewsDec 4, 2020
YouTubePractical Machinist
4:44
old machinist trick
1.8M viewsDec 4, 2014
YouTubeRasmus Rasmussen
33:29
BLUEPRINT READING PART 1, Marc L'Ecuyer
398.4K viewsNov 25, 2014
YouTubeTHATLAZYMACHINIST
8:37
Mechanical Aptitude Tests - Questions and Answers
761.7K viewsAug 8, 2018
YouTubeCareerVidz
See more videos
Static thumbnail place holder